This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
firmware:tina2 [2019/09/27 06:09] peter |
firmware:tina2 [2020/09/21 07:30] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | =====WEEDO | + | ===== WEEDO TINA2 Firmware Update |
---- | ---- | ||
- | ====V2.9 (2019.09.22)==== | + | ====V2.13(2020.06.02)==== |
- | ===update content:=== | + | [[https://drive.google.com/ |
- | - Compatible with the SparkOne network control box, the communication baud rate is 1000000bps. | + | |
- | - When the printer performs automatic wire feeding or automatic wire retracting, click the button to immediately stop the operation. | + | |
- | - Reduce the extrusion speed when the printer automatically feeds the wire. | + | |
- | Download: | + | ==== V2.11 (2019.11.10) |
+ | **Update content: | ||
- | ====V2.8 (2019.09.05)==== | + | **1. A host communication mode setting menu is added to the control interface.** |
- | ===update content: | + | The corresponding communication rate of Wiibuilder |
- | - Add WIFI network setting function through TF card file | + | |
- | - The file list is changed to paging mode to solve the problem | + | |
- | Download: | + | The firmware' |
+ | |||
+ | **2. Full support for Spark network control boxes.** | ||
+ | |||
+ | When connecting and disconnecting Spark, a prompt message is displayed on the screen.\\ | ||
+ | |||
+ | When Spark prints online, press the control key to display the online print menu, you can control to pause or cancel printing.\\ | ||
+ | |||
+ | During printing, the progress and elapsed time are displayed on the screen.\\ | ||
+ | |||
+ | After the Spark interface cancels printing, the printer automatically restarts and resets.\\ | ||
+ | \\ | ||
+ | <WRAP center round download 60%>\\ | ||
+ | [[http:// | ||
+ | </ | ||
+ | \\ | ||
+ | **Note: The original Octoprint system or the older version of SparkOne system need to be set according to the following tutorials to achieve all the above functions**\\ | ||
+ | <WRAP center round tip 60%>\\ | ||
+ | [[: | ||
+ | </ | ||
+ | \\ | ||
+ | \\ | ||
+ | ---- | ||
+ | ==== V2.10 (2019.10.07) ==== | ||
+ | **update content: | ||
+ | 1. Before printing starts, add the gcode file slice information interface (only the gcode files generated by Wiibuilder V2.0.6 and later versions, including complete slice information)\\ | ||
+ | |||
+ | 2. Add serial number display function in network device information interface\\ | ||
+ | |||
+ | 3. Add resume interface to improve the positioning accuracy of resume\\ | ||
+ | \\ | ||
+ | <WRAP center round download 60%>\\ | ||
+ | [[http:// | ||
+ | </ | ||
+ | \\ | ||
+ | |||
+ | ---- | ||
+ | |||
+ | ==== V2.9 (2019.09.22) ==== | ||
+ | **update content: | ||
+ | 1. Compatible with the SparkOne network control box, the communication baud rate is 1000000bps. | ||
+ | |||
+ | [[: | ||
+ | |||
+ | 2. When the printer is in the process of automatically feeding or unwinding, click the button to stop the operation immediately\\ | ||
+ | |||
+ | 3. Reduce the extrusion speed when the printer automatically feeds yarn\\ | ||
+ | \\ | ||
+ | <WRAP center round download 60%>\\ | ||
+ | [[http:// | ||
+ | </ | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ---- | ||
+ | ==== V2.8 (2019.09.05) ==== | ||
+ | **update content: | ||
+ | |||
+ | 1. Add WIFI network setting function through TF card file\\ | ||
+ | |||
+ | 2. The file list is changed to paging mode, which solves the problem of slow refresh of the file list\\ | ||
+ | \\ | ||
+ | <WRAP center round download 60%>\\ | ||
+ | [[http:// | ||
+ | </ | ||
+ | |||
+ | ---- |