This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
firmware:tina2 [2019/12/04 05:07] peter |
firmware:tina2 [2020/09/21 07:30] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== WEEDO TINA2 固件更新 | + | ===== WEEDO TINA2 Firmware Update |
---- | ---- | ||
+ | |||
+ | ====V2.13(2020.06.02)==== | ||
+ | |||
+ | [[https:// | ||
+ | |||
==== V2.11 (2019.11.10) ==== | ==== V2.11 (2019.11.10) ==== | ||
- | 更新内容:\\ | + | **Update content:**\\ |
- | 1. 控制界面中增加主机通讯模式设置菜单,Wiibuilder对应通讯速率为1000000bps,SparkOne对应通讯速率为57600bps。\\ | + | |
- | | + | **1. A host communication mode setting menu is added to the control interface.** |
- | 2. 全面支持Spark网络控制盒。\\ | + | |
- | | + | The corresponding communication rate of Wiibuilder |
- | Spark联机打印时,按下控制键会显示联机打印菜单,可控制暂停或取消打印 | + | |
- | | + | The firmware' |
- | Spark界面取消打印后,打印机自动重启复位 | + | |
+ | **2. Full support for Spark network control boxes.** | ||
+ | |||
+ | When connecting and disconnecting Spark, a prompt message is displayed on the screen.\\ | ||
+ | |||
+ | When Spark prints online, press the control key to display the online print menu, you can control to pause or cancel printing.\\ | ||
+ | |||
+ | During printing, the progress and elapsed time are displayed on the screen.\\ | ||
+ | |||
+ | After the Spark interface cancels printing, the printer automatically restarts and resets.\\ | ||
\\ | \\ | ||
- | [[http:// | + | <WRAP center round download 60%>\\ |
+ | [[http:// | ||
+ | </ | ||
+ | \\ | ||
+ | **Note: The original Octoprint system or the older version of SparkOne system need to be set according to the following tutorials to achieve all the above functions**\\ | ||
+ | <WRAP center round tip 60%>\\ | ||
+ | [[: | ||
+ | </ | ||
\\ | \\ | ||
- | **注意: | ||
- | [[octoprint_connect_tina2|OctoPrint连接Tina2教程]]\\ | ||
\\ | \\ | ||
---- | ---- | ||
==== V2.10 (2019.10.07) ==== | ==== V2.10 (2019.10.07) ==== | ||
- | 更新内容:\\ | + | **update content:**\\ |
- | 1. 在打印开始前,增加显示gcode文件切片信息界面(仅Wiibuilder V2.0.6及之后的版本生成的gcode文件,包含完整的切片信息)\\ | + | 1. Before printing starts, add the gcode file slice information interface |
- | 2. 在网络设备信息界面增加序列号显示功能\\ | + | |
- | 3. 增加恢复续打界面,完善续打的定位精度\\ | + | 2. Add serial number display function in network device information interface\\ |
+ | |||
+ | 3. Add resume interface to improve the positioning accuracy of resume\\ | ||
\\ | \\ | ||
- | [[http:// | + | <WRAP center round download 60%>\\ |
+ | [[http:// | ||
+ | </ | ||
\\ | \\ | ||
Line 30: | Line 53: | ||
==== V2.9 (2019.09.22) ==== | ==== V2.9 (2019.09.22) ==== | ||
- | 更新内容:\\ | + | **update content:**\\ |
- | 1. 兼容SparkOne网络控制盒,通讯波特率为1000000bps。[[octoprint_connect_tina2|OctoPrint连接TINA2教程]]\\ | + | 1. Compatible with the SparkOne |
- | 2. 打印机在执行自动进丝或自动退丝过程中,点击按键可立即中止操作\\ | + | |
- | 3. 降低打印机自动进丝时的挤出速度\\ | + | [[:octoprint_connect_tina2|How to Connect |
+ | |||
+ | 2. When the printer is in the process of automatically feeding or unwinding, click the button to stop the operation immediately\\ | ||
+ | |||
+ | 3. Reduce the extrusion speed when the printer automatically feeds yarn\\ | ||
\\ | \\ | ||
- | [[http:// | + | <WRAP center round download 60%>\\ |
+ | [[http:// | ||
+ | </ | ||
\\ | \\ | ||
---- | ---- | ||
==== V2.8 (2019.09.05) ==== | ==== V2.8 (2019.09.05) ==== | ||
- | 更新内容:\\ | + | **update content:**\\ |
- | 1. 增加通过TF卡文件进行WIFI网络设置功能\\ | + | |
- | 2. 文件列表改为分页模式,解决文件列表刷新慢的问题\\ | + | 1. Add WIFI network setting function through TF card file\\ |
+ | |||
+ | 2. The file list is changed to paging mode, which solves the problem of slow refresh of the file list\\ | ||
\\ | \\ | ||
- | [[http:// | + | <WRAP center round download 60%>\\ |
+ | [[http:// | ||
+ | </ | ||
+ | |||
+ | ---- |