firmware:tina2
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
firmware:tina2 [2019/12/04 05:20] peter |
firmware:tina2 [2020/09/21 07:30] (current) |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| ---- | ---- | ||
| + | |||
| + | ====V2.13(2020.06.02)==== | ||
| + | |||
| + | [[https:// | ||
| + | |||
| ==== V2.11 (2019.11.10) ==== | ==== V2.11 (2019.11.10) ==== | ||
| - | update | + | **Update |
| - | 1. A host communication mode setting menu is added to the control interface. The corresponding communication rate of Wiibuilder is 1000000bps and the corresponding communication rate of SparkOne is 57600bps.\\ | + | |
| - | The firmware' | + | **1. A host communication mode setting menu is added to the control interface.** |
| - | 2. Full support for Spark network control boxes.\\ | + | |
| - | When connecting and disconnecting Spark, a prompt message is displayed on the screen. | + | The corresponding communication rate of Wiibuilder is 1000000bps and the corresponding communication rate of SparkOne is 57600bps.\\ |
| - | When Spark prints online, press the control key to display the online print menu, you can control to pause or cancel printing. | + | |
| - | During printing, the progress and elapsed time are displayed on the screen. | + | The firmware' |
| - | After the Spark interface cancels printing, the printer automatically restarts and resets. | + | |
| + | **2. Full support for Spark network control boxes.** | ||
| + | |||
| + | When connecting and disconnecting Spark, a prompt message is displayed on the screen.\\ | ||
| + | |||
| + | When Spark prints online, press the control key to display the online print menu, you can control to pause or cancel printing.\\ | ||
| + | |||
| + | During printing, the progress and elapsed time are displayed on the screen.\\ | ||
| + | |||
| + | After the Spark interface cancels printing, the printer automatically restarts and resets.\\ | ||
| \\ | \\ | ||
| - | [[http:// | + | <WRAP center round download 60%>\\ |
| + | [[http:// | ||
| + | </ | ||
| \\ | \\ | ||
| **Note: The original Octoprint system or the older version of SparkOne system need to be set according to the following tutorials to achieve all the above functions**\\ | **Note: The original Octoprint system or the older version of SparkOne system need to be set according to the following tutorials to achieve all the above functions**\\ | ||
| - | [[octoprint_connect_tina2|octoprint_connect_tina2]]\\ | + | <WRAP center round tip 60%>\\ |
| + | [[:octoprint_connect_tina2|How to Connect TINA2 To Octoprint]] | ||
| + | </ | ||
| + | \\ | ||
| \\ | \\ | ||
| ---- | ---- | ||
| ==== V2.10 (2019.10.07) ==== | ==== V2.10 (2019.10.07) ==== | ||
| - | update content:\\ | + | **update content:**\\ |
| 1. Before printing starts, add the gcode file slice information interface (only the gcode files generated by Wiibuilder V2.0.6 and later versions, including complete slice information)\\ | 1. Before printing starts, add the gcode file slice information interface (only the gcode files generated by Wiibuilder V2.0.6 and later versions, including complete slice information)\\ | ||
| + | |||
| 2. Add serial number display function in network device information interface\\ | 2. Add serial number display function in network device information interface\\ | ||
| + | |||
| 3. Add resume interface to improve the positioning accuracy of resume\\ | 3. Add resume interface to improve the positioning accuracy of resume\\ | ||
| \\ | \\ | ||
| - | [[http:// | + | <WRAP center round download 60%>\\ |
| + | [[http:// | ||
| + | </ | ||
| \\ | \\ | ||
| Line 30: | Line 53: | ||
| ==== V2.9 (2019.09.22) ==== | ==== V2.9 (2019.09.22) ==== | ||
| - | update content: | + | **update content:**\\ |
| - | 1. Compatible with SparkOne network control box, communication baud rate is 1000000bps.[[octoprint_connect_tina2|octoprint_connect_tina2]]\\ | + | 1. Compatible with the SparkOne network control box, the communication baud rate is 1000000bps. |
| + | |||
| + | [[:octoprint_connect_tina2|How to Connect TINA2 To Octoprint]]\\ | ||
| 2. When the printer is in the process of automatically feeding or unwinding, click the button to stop the operation immediately\\ | 2. When the printer is in the process of automatically feeding or unwinding, click the button to stop the operation immediately\\ | ||
| + | |||
| 3. Reduce the extrusion speed when the printer automatically feeds yarn\\ | 3. Reduce the extrusion speed when the printer automatically feeds yarn\\ | ||
| \\ | \\ | ||
| - | [[http:// | + | <WRAP center round download 60%>\\ |
| + | [[http:// | ||
| + | </ | ||
| \\ | \\ | ||
| ---- | ---- | ||
| ==== V2.8 (2019.09.05) ==== | ==== V2.8 (2019.09.05) ==== | ||
| - | update content:\\ | + | **update content:**\\ |
| 1. Add WIFI network setting function through TF card file\\ | 1. Add WIFI network setting function through TF card file\\ | ||
| + | |||
| 2. The file list is changed to paging mode, which solves the problem of slow refresh of the file list\\ | 2. The file list is changed to paging mode, which solves the problem of slow refresh of the file list\\ | ||
| \\ | \\ | ||
| - | [[http:// | + | <WRAP center round download 60%>\\ |
| + | [[http:// | ||
| + | </ | ||
| + | |||
| + | ---- | ||
firmware/tina2.1575436831.txt.gz · Last modified: 2020/09/21 07:28 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
